Numerical Methods in Civil Engineering

Numerical Methods in Civil Engineering

Comparative Thermal Behaviour of Unprotected and Protected Steel, Stainless Steel, and Aluminium Framed Buildings Exposed to Standard Fire

Document Type : Research

Authors
1 Ph.D. Candidate, Department of Structural Engineering, MBM University, Jodhpur, India
2 Professor, Department of Structural Engineering, MBM University, Jodhpur, India
Abstract
Fire significantly influences the thermal and structural behaviour of metallic-framed buildings by reducing strength and stability at elevated temperatures. This study presents a comparative thermo-mechanical assessment of steel, stainless steel, and aluminium-framed buildings subjected to fire. For the comparative analysis, we modelled a three-storey (G+2) building and analysed it under a 30-minute standard fire exposure using the finite element software Abaqus. The G+2 building comprises a ground floor plus two upper stories. The results show that, due to fire, the building experiences increased stress and plastic strain accumulation regardless of the type of metal (Steel, Stainless steel, or Aluminium) used in its construction. We also evaluated the critical temperature, which was lowest for the stainless steel frame and highest for the aluminium frame, while the steel frame exhibited intermediate behaviour. Further reaction force analysis indicated that stainless steel retained the highest load-carrying capacity during fire, steel showed moderate performance, while aluminium experienced the fastest degradation in structural strength. In addition, we studied the role of a passive fire protection layer in mitigating the fire-induced instability. We evaluated different thicknesses of magnesium oxide board (1-15 cm) under a 30-minute standard fire temperature and found that it reduced the temperature by 11.14% to 95.41%, respectively. The minimum required thickness of magnesium oxide board to preserve the building’s structural integrity for 30 minutes was also determined based on the critical temperature. It was found to lie in the range of 8-11 cm for different metals considered in this study.
Keywords
Subjects

[1] Amin, A., Tamal, S., Bari, A. K. M. F., Mazumder, M., & Hasan, M. A. (2022). Strengthening of fire-damaged reinforced beams by using ferro cement. Turkish Journal of Engineering, 6(3), 206-210. https://doi.org/10.31127/tuje.925199
[2] Liu, Y. J., & Li, H. N. (2004). Review and prospect of the study on behaviour of structures in fire conditions. Journal of Disaster Prevention and Mitigation Engineering, 24(2), 219-225.
[3] Ahmed, A. D., & Güneyisi, E. (2022). Lateral response of double skin tubular column to steel beam composite frames. Turkish Journal of Engineering, 6(1), 16-25. https://doi.org/10.31127/tuje.749730
[4] Jelčić Rukavina, M., Skejić, D., Kralj, A., Ščapec, T., & Milovanović, B. (2022). Development of lightweight steel-framed construction systems for nearly-zero energy buildings. Buildings, 12(7), 929. https://doi.org/10.3390/buildings12070929
[5] Czerwinski, F. (2020). Thermal stability of aluminium alloys. Materials, 13(15), 3441. https://doi.org/10.3390/ma13153441
[6] Şahbaz, M. (2022). Comparison of experimental and numerical analysis of Quasi-Static punch shear test for stainless steel sheet material. Turkish Journal of Engineering, 6(4), 306-312. https://doi.org/10.31127/tuje.1002507
[7] You, X., Xing, Z., Jiang, S., Zhu, Y., Lin, Y., Qiu, H.,& Chen, Y. (2024). A review of research on aluminium alloy materials in structural engineering. Developments in the built environment, 17, 100319. https://doi.org/10.1016/j.dibe.2023.100319
[8] Suman, S., & Samanta, A. (2020, March). Behaviour of Unrestrained Steel I-Section Beams in Case of Fire. In Indian Structural Steel Conference (pp. 737-748). Singapore: Springer Nature Singapore. https://doi.org/10.1007/978-981-19-9390-9_60
[9] Ibraheem, O. F., & Abdullah, H. A. (2022). Behaviour of Steel Beams Subjected to Bending and Shear Loading Under Localized Fire Conditions. Tikrit Journal of Engineering Sciences, 29(3), 82-90. https://doi.org/10.25130/tjes.29.3.9
[10] Saleh, S. M., & Al-abboodi, İ. (2021). Strength and behaviour assessment of axially loaded concrete filled steel tubular stub columns. Turkish Journal of Engineering, 5(4), 154-164. https://doi.org/10.31127/tuje.686246
[11] İlgün, A., Zıa, A. J., Sancıoğlu, S., Soydoğan, H. F., Köklü, M. H., Arıbaş, S., & Bayram, B. (2023). Buckling performance of thin-walled filled steel columns. Turkish Journal of Engineering, 7(3), 172-179. https://doi.org/10.31127/tuje.1092975
[12] Quan, C., Murtaza, H., & Kucukler, M. (2023). Resistance and behaviour of carbon steel and stainless steel columns with axial and rotational end‐restraints in fire. ce/papers, 6(3-4), 2214-2219. https://doi.org/10.1002/cepa.2508Digital Object Identifier (DOI)
[13] T. Hozjan, I. Planinc, M. Saje, S. Srpcic. (2008). Buckling of restrained steel columns due to fire conditions. Steel and Composite Structures, 8, 2, 159-178. https://doi.org/10.12989/scs.2008.8.2.159
[14] Taghipour Anvari, A., Mahamid, M., McNallan, M., & Eslami, M. (2019). Effectiveness of damaged fireproofing in structural steel members subjected to fire. Journal of structural fire engineering, 10(1), 24-47. https://doi.org/10.1108/JSFE-11-2017-0044
[15] Aghabozorgi, P., Laím, L., & Santiago, A. (2025). Numerical and Design Analysis of Protected Steel Columns in Standard Fire: P. Aghabozorgi et al. Fire Technology, 61(5), 3093-3135. https://doi.org/10.1007/s10694-025-01716-y
[16] Bureau of Indian Standards. (1964). SP 6: (1), Handbook for structural engineers – Structural steel sections, New Delhi.
[17] Eurocode 3: Design of steel structures – Part 1 – 2: General rules – Structural fire design, EN-1993-1-2, 2005.
[18] Eurocode 9: Design of aluminium structures – Part 1 – 2: Structural fire design, EN-1999-1-2, 2007.
[19] Steau, E., & Mahendran, M. (2021). Elevated temperature thermal properties of fire protective boards and insulation materials for light steel frame systems. Journal of Building Engineering, 43, 102571. https://doi.org/10.1016/j.jobe.2021.102571
[20] Bureau of Indian Standards. (1987). IS 875-Part 2, Code of Practice for Design Loads (Other Than Earthquake) For Buildings and Structures, New Delhi.
[21] The European Union. (2002). EN-1991-1-2, Eurocode 1: Actions on structures, in Part 1-2: Actions on structures exposed to fire.
[22] Lu, W., D’Mello, C., & Ayoub, A. (2020). Coupled thermomechanical damage modeling for structural steel in fire conditions. Journal of Structural Engineering, 146(7), 04020127. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002652
[23] Zhu, G. M., Kang, Y. L., Chen, W., & Ma, G. T. (2008, April). 3D thermal mechanical coupled elasto-plastic finite element analysis in the whole rolling process of H-beam. In Materials Science Forum (Vol. 575, pp. 532-538). Trans Tech Publications Ltd. https://doi.org/10.4028/www.scientific.net/MSF.575-578.532
[24] BATOUNGUIDIO, S.A.M., & XUE, J. (2025). Finite Element Analysis of Steel Beams under Fire Exposure: The Impact of Geometric and Material Nonlinearity on Fire Resistance. International Journal of Research, 12(6). https://doi.org/10.5281/zenodo.15672233
[25] Ramesh, S., Choe, L., & Zhang, C. (2020). Experimental investigation of structural steel beams subjected to localized fire. Engineering structures, 218, 110844. https://doi.org/10.1016/j.engstruct.2020.110844
[26] Rubert, A., & Schaumann, P. (1986). Structural steel and plane frame assemblies under fire action. Fire Safety Journal, 10(3), 173-184. https://doi.org/10.1016/0379-7112(86)90014-7
[27] Bureau of Indian standards. (2007). IS 800:2007, General Construction in Steel-Code of Practice, New Delhi.
[28] Xing, Y., Wang, W., & Al-azzani, H. (2021). Assessment of thermal properties of various types of high-strength steels at elevated temperatures. Fire Safety Journal, 122, 103348.
[29]Pournaghshband, A., Afshan, S., & Theofanous, M. (2019, December). Elevated temperature performance of restrained stainless steel beams. In Structures (Vol. 22, pp. 278-290). Elsevierhttps://doi.org/10.1016/j.istruc.2019.08.015Get rights and content
[30] Rodrigues, J. C., Neves, I. C., & Valente, J. C. (2000). Experimental research on the critical temperature of compressed steel elements with restrained thermal elongation. Fire Safety Journal, 35(2), 77-98. https://doi.org/10.1016/S0379-7112(00)00018-7
[31] Allam, A., Nassif, A., & Nadjai, A. (2019). Behaviour of restrained steel beam at elevated temperature–parametric studies. Journal of Structural Fire Engineering, 10(3), 324-339. https://doi.org/10.1108/JSFE-11-2018-0036
[32] Wang, W., Zhang, L., Ge, Y., & Xu, L. (2018). Behaviour of restrained high strength steel columns at elevated temperature. Journal of Constructional Steel Research, 148, 251-264. https://doi.org/10.1016/j.jcsr.2018.05.022
[33] Lopes, N., Vila Real, P. M. M., Piloto, P. A. G., Mesquita, L. M. R., & Silva, L. S. (2006). Numerical modelling of the behaviour of a stainless steel portal frame subjected to fire.
[34] Maljaars, J., Soetens, F., & Snijder, H. H. (2010). Local buckling of fire-exposed aluminum members: New design model. Journal of structural engineering, 136(1), 66-75. https://doi.org/10.1061/(ASCE)ST.1943-541X.00000
[35] Milan, D., Torić, N., & Boko, I. (2022). Performance analysis of a simple aluminium structure in fire conditions. Advances in Civil and Architectural Engineering, 13(24), 12-22. https://doi.org/10.13167/2022.24.2
[36] Zanoni, A. L., Piloto, P. A., Mesquita, L., Rossetto, D. R., Lopes, N., & Vila Real, P. (2025). Fire resistance of stainless steel beams: different sections and grades. Journal of Structural Fire Engineering, 16(4), 566-593. https://doi.org/10.1108/JSFE-05-2025-0019
[37] Chen, T., Fan, S., Xu, Q., Xu, K., Luo, J., & Tang, Y. (2024). Research on mechanical properties of duplex stainless steel S22053 at elevated temperature and after fire. Thin-Walled Structures, 197, 111620. 10.1016/j.tws.2024.111620
[38]Choi, I. R., Chung, K. S., & Lee, H. (2017). Thermal and mechanical properties of structural steel SN400 at elevated temperatures. International Journal of Steel Structures, 17(3), 999-1007. https://doi.org/10.1007/s13296-017-9011-z
[39] Sabtu, M. A., Admi, A. E., Salleh, M. M., Osman, S. A., & Osman, S. A. (2024). Finite Element Analysis of Stress Distribution in AL6061 Frame Structures Under Varying Applied Loads. International Journal of Integrated Engineering, 16(2), 259-269.
[40] Petre, M., Dinu, C., Drăghici, N. C., & Andrei, V. (2020). Prediction of the residual stress after quenching of 6061 aluminium alloy plates by using mathematical modelling. In ITM Web of Conferences (Vol. 34, p. 02007). EDP Sciences.
[41] Cai, Y., Ho, H. W., Li, S., & Mensinger, M. (2025). Structural Metals after Exposure to High Temperatures: Residual Mechanical Properties and Predictions. steel research international, 96(7), 2400610. https://doi.org/10.1002/srin.202400610
[42] Zayniddinov, N., Volokhov, G., & Abdurasulov, S. (2025). Characterization and assessment of rolling stock structural durability under elevated operating temperatures. Vibroengineering Procedia, 60, 165-171.
[43] Džolev, I., Kekez-Baran, S., & Rašeta, A. (2025). Fire Resistance of Steel Beams with Intumescent Coating Exposed to Fire Using ANSYS and Machine Learning. Buildings, 15(13), 2334. https://doi.org/10.3390/buildings15132334
Aghabozorgi, P., Laím, L., & Santiago, A. (2024). A Numerical Investigation On Fire Performance Of Industrial Steel Warehouses Protected With Gypsum‐Based Boards. ce/papers, 7(1-2), 175-185.  https://doi.org/10.1002/cepa.3034
Volume 10, Issue 4
Spring 2026
Pages 108-119

  • Receive Date 25 June 2026
  • Revise Date 25 October 2026
  • Accept Date 22 November 2026