Volume 1, Issue 1 (9-2016)                   NMCE 2016, 1(1): 57-63 | Back to browse issues page

XML Print

Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Samani H R, Mirtaheri M. Seismic response sensitivity of the structures equipped with cylindrical frictional dampers to the value of slippage load. NMCE 2016; 1 (1) :57-63
URL: http://nmce.kntu.ac.ir/article-1-36-en.html
1- Ph.D. candidate, Civil Engineering Department , K.N. Toosi University of Technology, Tehran, Iran
2- Associate Professor, Civil Engineering Department , K.N. Toosi University of Technology, Tehran, Iran
Abstract:   (2263 Views)
Cylindrical Frictional Damper (CFD) is a new revolutionary frictional based mechanical damper. Unlike the other types of frictional dampers, CFDs do not utilize bolts to produce friction between contact surfaces. These dampers consist of two main parts, the inner shaft and the external cylinder. These two parts are assembled such that one is shrink-fitted inside the other. In this investigation, seismic response of steel structures equipped with CFDs is studied. Special attention is given to the sensitivity of the seismic response to the value of the slippage load. To do so, the optimum slippage load of the structure (the slippage loads which results in minimum displacement response) is obtained for various seismic excitations. The seismic response of the structure is obtained for various slippage loads in the range of plus and minus %20 of the optimum slippage load. Moreover the seismic performance of steel structures equipped CFDs is investigated using non-linear time history analyses. The results show that value of the optimum slippage load is completely dependent to seismic excitation. It is further shown that if the slippage load has a difference up to 20% from its optimum value, the maximum displacement response can increases up to 35%, however, it is still less than the maximum displacement response of the frame without CFDs. It was also shown that CFD can significantly improve the performance of steel structures subjected to earthquake loads.
Full-Text [PDF 697 kb]   (925 Downloads)    
Type of Study: Research | Subject: Special
Received: 2013/09/16 | Revised: 2013/12/7 | Accepted: 2014/04/3 | ePublished ahead of print: 2014/04/13

1. [1] Pall AS, Marsh C. Response of friction damped braced frames. J Struct Eng-ASCE 1982;108(9):1313-23.
2. [2] Wua B, Zhanga J, Williams b MS, OuaJ. Hysteretic behavior of improved Pall-typed frictional dampers.EngStruct 2005;27:1258-67. [DOI:10.1016/j.engstruct.2005.03.010]
3. [3] Aiken ID, Kelly JM. Earthquake simulator testing and analytical studies of two energy-absorbing systems for multistory structures. Report no. UCB/EERC- 90/03. Berkeley (CA): Earthquake Engineering Research Center. University of California; 1990.
4. [4] Nims DK. et al. Application of the energy dissipating restraint to buildings.In: Proc. ATC 17-1 on seismic isolation, energy dissipation, and active control.1993. p. 627-38.
5. [5] Constantinou MC, Mokha A, Reinhorn AM. Teflon bearings in base isolation, II: modeling. J Struct Eng 1990;116(2):455-74. [DOI:10.1061/(ASCE)0733-9445(1990)116:2(455)]
6. [6] Mualla IH, Belev B. Performance of steel frames with a new friction damper device under earthquake excitation. EngStruct 2002;24(3):365-71. [DOI:10.1016/S0141-0296(01)00102-X]
7. [7] Monir HS, Zeynali K. A modified friction damper for diagonal bracing of structures. J Constr Steel Res 2013;87:17-30 [DOI:10.1016/j.jcsr.2013.04.004]
8. [8] Mirtaheri M, Zandi AP, Samadi SS, Samani HR. Numerical and experimental study of hysteretic behavior of cylindrical friction dampers. EngStruct 2011;33:3647-56. [DOI:10.1016/j.engstruct.2011.07.029]
9. [9] Min KW, Seong J.Y, Kim J. Simple design procedure of a friction damper for reducing seismic responses of a single-story structure. Eng Struct 2010; 32:3539-3547 [DOI:10.1016/j.engstruct.2010.07.022]
10. [10] SEONG JY, MIN K. An Analytical Approach for Design of a Structure Equipped with Friction Dampers. Procedia Engineering 2011;14: 1245-1251 [DOI:10.1016/j.proeng.2011.07.156]
11. [11] Lee SH, Park JH, Lee SK, Min KW. Allocation and slip load of friction dampers for a seismically excited building structure based on storey shear force distribution. Eng Struct 2008;30:930-40. [DOI:10.1016/j.engstruct.2007.03.020]
12. [12] Fus Y, Cherry S. Design of friction damped structures using lateral force procedure. Earthquake Engng Struct. Dyn. 2000; 29: 989-1010 https://doi.org/10.1002/1096-9845(200007)29:7<989::AID-EQE950>3.3.CO;2-Z [DOI:10.1002/1096-9845(200007)29:73.3.CO;2-Z]

Add your comments about this article : Your username or Email: