Volume 5, Issue 3 (3-2021)                   NMCE 2021, 5(3): 1-12 | Back to browse issues page


XML Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Khosravi M, Ramezanzadeh A, Zare S. Evaluation of Disc Cutter Performance in Rock Cutting Process Using 3D Finite Element Method. NMCE 2021; 5 (3) :1-12
URL: http://nmce.kntu.ac.ir/article-1-307-en.html
1- PhD Student of Rock Mechanics, Faculty of Mining, Petroleum & Geophysics Engineering, Shahrood University of Technology, Shahrood, Iran. , mortezakhosravi80@gmail.com
2- Associate Professor, Faculty of Mining, Petroleum & Geophysics Engineering, Shahrood University of Technology
Abstract:   (1086 Views)
Today, numerical simulation can be used as a suitable tool to measure large quantities that are very expensive and, in some cases, impossible to measure. One of the important issues in predicting rock mass boreability in excavation with full face tunnel boring machines is estimating the disc's forces for rock cutting. For this purpose, the linear cutting test is  employed. However, limited access to equipment and the high cost of this test have resulted in a decline in its use. In this research, linear cutting tests have been simulated using numerical methods using ABAQUS 6-14 software, which is based on the finite element method. In this simulation, according to the dynamic analysis, for the explicit solution method and the behavior of the rock, the Johnson–Holmquist-II model (JH-2) is used. Subsequently, after solving the model, the forces acting on a fixed cross-sectional disc are estimated, and then, for validation, the results of numerical modeling are compared with laboratory results and theoretical model. Comparison of the results shows that the cutting forces obtained from the simulation have a deviation of 7% and 11% with normal and rolling forces compared to the mean forces in laboratory work, respectively.
Full-Text [PDF 1031 kb]   (660 Downloads)    
Type of Study: Applicable | Subject: General
Received: 2020/12/2 | Revised: 2021/01/18 | Accepted: 2021/02/7 | ePublished ahead of print: 2021/02/15

References
1. Taban M, Hajiazizi M, Ghobadian R. (2019). Predicting the value of the rock quality index in the Q-system using gene expression programming. Numerical Methods in Civil Engineering, Vol. 4, No. 2. [DOI:10.52547/nmce.4.2.44]
2. Cook N, Hood M, Tsai F. (1984). In Observations of crack growth in hard rock loaded by an indenter. International Journal of Rock Mechanics and Mining Sciences & Geomechanics, 97-107. [DOI:10.1016/0148-9062(84)91177-X]
3. Liu HY, Kou SQ, Lindqvist CA. (2002). A numerical simulation of the rock fragmentation process induced by indenters. Int J Rock Mech Min Sci 39:491-505 [DOI:10.1016/S1365-1609(02)00043-6]
4. Baek SH, Moon HK. (2003). A numerical study on the rock fragmentation by TBM cutter penetration. Tunn Undergr Space (J Korean Soc Rock Mech) 13(6):444-454
5. Gong Q.M, Zhao J, Jiao Y.Y. (2005). Numerical modeling of the effects of joint orientation on rock fragmentation by TBM cutters. Tunnelling and Underground Space Technology, vol. 20, PP. 183-191. [DOI:10.1016/j.tust.2004.08.006]
6. Gong Q.M, Jiao Y.Y, Zhao J. (2006a). Numerical modelling of the effects of joint spacing on rock fragmentation by TBM cutters. Tunnelling and Underground Space Technology, vol. 21, PP. 46-55. [DOI:10.1016/j.tust.2005.06.004]
7. Rojek J, Labra C, Oñate E. (2010). Discrete Element Simulation of Rock Cutting Processes. Modern Building Materials, Structures and Techniques - The 10th International Conference.
8. Gong Q.M, Zhao J, Hefny A.M. (2006b). Numerical simulation of rock fragmentation process induced by two TBM cutters and cutter spacing optimization. Tunnelling and Underground Space Technology, vol. 21, p. 263. [DOI:10.1016/j.tust.2005.12.124]
9. Mabra C. (2012). Development of the Discrete Element Method for Excavation Processes. International Center for Numerical Methods in Engineering Gran Capitán. Barcelona, Spain.
10. Li H.Y, Shi G.Y. (2012). The Numerical Simulations of Forces Acting on TBM Disc Cutters with the Consideration of Confining Pressure and Damage in Rocks. Applied Mechanics and Materials, vol. 105-107, PP. 1170-1174. [DOI:10.4028/www.scientific.net/AMM.105-107.1170]
11. Medel-Morales R.C, Botello-Rionda S. (2013). Design and Optimization of Tunnel Boring Machines by Simulating the Cutting Rock Process using the Discrete Element Method, Computación Sistema, vol. 17, PP. 329-339.
12. Mohammadi Reza. (2015). Numerical modeling of rock cutting in TBM tunneling. Master's Thesis, Faculty of Mine Engineering, University of Zanjan, Iran.
13. Huiyun Li1, and Erxia Du. (2016). Simulation of rock fragmentation induced by a tunnel boring machine disk cutter. Advances in Mechanical Engineering, Vol. 8(6) 1-11. DOI: 10.1177/1687814016651557 [DOI:10.1177/1687814016651557]
14. Gong Q, He G, Zhao X, Ma H, Li X, Zhang H, Miao C. (2015). Influence of different cutter spacings on rock fragmentation efficiency of Beishan granite by TBM. Chinese Journal of Geotechnical Engineering, 37(1): 53-60.
15. Xia Y, Guo B, Cong G, Zhang X, Zeng G. (2017). Numerical simulation of rock fragmentation induced by a single TBM disc cutter close to a side free surface. International Journal of Rock Mechanics and Mining Sciences 91:40-8. [DOI:10.1016/j.ijrmms.2016.11.004]
16. Zhiqiang Zhang1, Kangjian Zhang · Weijie Dong· Biao Zhang. (2020). Study of Rock‑Cutting Process by Disc Cutters in Mixed Ground based on Three‑dimensional Particle Flow Model, Rock Mechanics and Rock Engineering [DOI:10.1007/s00603-020-02118-y]
17. Labra C, Rojek J, Onate E. (2016). Discrete/Finite Element Modelling of Rock Cutting with a TBM Disc Cutter. Rock Mech Rock Eng, DOI 10.1007/s00603-016-1133-7. [DOI:10.1007/s00603-016-1133-7]
18. Gang L, Lida Z. (2012). A Method to Predict Disc Cutter Specific Energy for TBM Based on CSM Model. Applied Mechanics and Materials. Vol 236-237, pp 414-417. [DOI:10.4028/www.scientific.net/AMM.236-237.414]
19. Sahir Butt, and G¨unther Meschke. (2017). A 3D peridynamic model of rock cutting with TBM disc cutters, Proceedings of the 7th GACM Colloquium on Computational MechanicsAt: Stuttgart, Germany.
20. Shaoquan K. (1995). Some basic problems in rock breakage by blasting and by indentation. Doctoral Thesis Lulea University of Technology, Lulea, Sweden.
21. Rostami J. (2013). Study of pressure distribution within the crushed zone in the contact area between rock and disc cutters. International Journal of Rock Mechanics and Mining Sciences 57, 172-186. [DOI:10.1016/j.ijrmms.2012.07.031]
22. Seungoong L, Sung h. (2009). Numerical Analysis on Fragmentation Mechanism by Indentation of Disc Cutter in a Rock Specimen with a Single Joint. Tunnel & Underground Space. Vol 19, No 5, pp 440-449.
23. Yucong Pan, Quansheng Liu1, Qi Liu, Jianping Liu, Xingxin Peng, Xing Huang, Mingbao Wei. (2019). Full-scale linear cutting tests to check and modify a widely used semitheoretical model for disc cutter cutting force prediction, Acta Geotechnica.
24. Sungong C, Seungoong L. (2015). Numerical Study to Estimate the Cutting Power on a Disc Cutter in Jointed Rock Mass. KSCE Journal of Civil Engineering.
25. Bo Ning, YiMin Xia, Laikuang Lin, Xuhui Zhang, YuanFu He, Yifan Liu. (2020). Experimental study on the adaptability of cutters with different blade widths under hard rock and extremely hard rock conditions, Acta Geotechnica, [DOI:10.1007/s11440-020-00958-0]
26. Yagiz S, Rostami J. (2012). Colorado School of Mines approach for predicting TBM performance. ISRM International symposium, 28-30 May.
27. Gertscha R, Gertschb L, Rostami J. (207). Disc cutting tests in Colorado Red Granite: Implications for TBM performance prediction. International Journal of Rock Mechanics & Mining Sciences 44 (2007) 238-246. [DOI:10.1016/j.ijrmms.2006.07.007]
28. Banadaki M, Mohanty B. (2012). Numerical simulation of stress wave induced fracture in rock. Int J Impact Eng, 40-41:16-25. [DOI:10.1016/j.ijimpeng.2011.08.010]
29. Xia Y.M, Guo B, Cong G.Q, Zhang X.H, Zeng G.Y. (2017). Numerical simulation of rock fragmentation induced by a single TBM disc cutter close to a side free surface. International Journal of Rock Mechanics and Mining Sciences,91,40-48. [DOI:10.1016/j.ijrmms.2016.11.004]
30. Abaqus 6.14 (2014). Analysis user's guide. Simulation Corp, Providence, RI, USA.
31. Ericsson A. (2010). Adams modelling of contact forces between disc cutter and mount. Master's Thesis, Department of Applied Mechanics Division of Dynamics. Chalmers University of Technology. Göteborg.

Add your comments about this article : Your username or Email:
CAPTCHA

Send email to the article author