Volume 5, Issue 2 (Special Issue “Recent Achievements in Endurance Time Method” 2020)                   NMCE 2020, 5(2): 12-20 | Back to browse issues page


XML Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Shirkhani A, Farahmand Azar B, Charkhtab Basim M. Evaluation of efficiency index of friction energy dissipation devices using endurance time method. NMCE 2020; 5 (2) :12-20
URL: http://nmce.kntu.ac.ir/article-1-297-en.html
1- PhD Candidate, Department of Structural Engineering, Faculty of Civil Engineering, University of Tabriz, Tabriz, Iran.‎
2- Associate Professor, Department of Structural Engineering, Faculty of Civil Engineering, University of ‎Tabriz, Tabriz, Iran. , b-farahmand@tabrizu.ac.ir ‎
3- Assistant Professor, Faculty of Civil Engineering, Sahand University of Technology, Tabriz, Iran.‎
Abstract:   (1139 Views)
Various methods have been presented to improve the performance of buildings against earthquakes. Friction damper device is one of the energy dissipation devices that appropriately absorbs and dissipates the input energy and decreases displacements. In this paper, the possibility of using endurance time method to determine the efficiency index and optimum slip load for these dampers was investigated by comparing the results of endurance time and nonlinear time history analyses. The efficiency indexes acquired from the average of results for nonlinear time history and endurance time analyses were close to each other. In this research, by assuming identical optimum slip load for the dampers in all stories, the normalized damper strength was increased in a number of equal steps ranging from zero to one to determine the efficiency index of dampers in each step. Then, the optimum slip load of dampers in the steel frames was calculated according to the minimum efficiency index of dampers. As a result, employing the endurance time method instead of a high number of nonlinear time history analyses is also possible, and using the endurance time method diminishes 57% of computational endeavors.  Lastly, a relation for acquiring the optimum slip load of the friction damper devices in steel structures was proposed in terms of the weight of the structures. After adding optimal FDDs to the structures and investigating the effectiveness of the dampers, it was concluded that by using endurance time excitation function with better energy consistency, the endurance time results could be improved.
Full-Text [PDF 1037 kb]   (488 Downloads)    
Type of Study: Research | Subject: Special
Received: 2020/10/6 | Revised: 2020/11/6 | Accepted: 2020/12/6

References
1. [1] Moradi-Moghadam, A.R., (2010). The Application of Friction Damper in Seismic Upgraded of Steel Structure with masonry infill, MSc thesis (in Persian), Islamic Azad University-Tehran Branch, Tehran.
2. [2] Mualla, I. H., & Belev, B. (2002). Performance of steel frames with a new friction damper device under earthquake excitation. Engineering Structures, 24(3), 365-371. [DOI:10.1016/S0141-0296(01)00102-X]
3. [3] Mualla, I., & Belev, B. (2015). Analysis, design and applications of rotational friction dampers for seismic protection. Czasopismo Inżynierii Lądowej, Środowiska i Architektury, 62(4), 335-346. [DOI:10.7862/rb.2015.199]
4. [4] Nielsen, L. O., & Mualla, I. H. (2002). A Friction damping system: Low order behavior and design, Department of Civil Engineering DTU-bygning, R-0302002, 2002.
5. [5] Naeem, A., & Kim, J. (2020). Seismic retrofit of structures using rotational friction dampers with restoring force. Advances in Structural Engineering, 23(16), 1-16. [DOI:10.1177/1369433220939213]
6. [6] Nabid, N., Hajirasouliha, I., & Petkovski, M. (2019). Simplified method for optimal design of friction damper slip loads by considering near-field and far-field ground motions. Journal of Earthquake Engineering, 1-25. [DOI:10.1080/13632469.2019.1605316]
7. [7] Estekanchi, H. E., & Basim, M. C. (2011). Optimal damper placement in steel frames by the Endurance Time method. The Structural Design of Tall and Special Buildings, 20(5), 612-630. [DOI:10.1002/tal.689]
8. [8] Estekanchi, H. E., Valamanesh, V., & Vafai, A. (2007). Application of endurance time method in linear seismic analysis. Engineering Structures, 29(10), 2551-2562. [DOI:10.1016/j.engstruct.2007.01.009]
9. [9] Basim, M. C., & Estekanchi, H. E. (2015). Application of endurance time method in performance-based optimum design of structures. Structural safety, 56, 52-67. [DOI:10.1016/j.strusafe.2015.05.005]
10. [10] Mirfarhadi, S. A., & Estekanchi, H. E. (2020). Value based seismic design of structures using performance assessment by the endurance time method. Structure and Infrastructure Engineering, 1-19. [DOI:10.1080/15732479.2020.1712436]
11. [11] Estekanchi, H. E., Mashayekhi, M., Vafai, H., Ahmadi, G., Mirfarhadi, S. A., & Harati, M. (2020). A state-of-knowledge review on the Endurance Time Method. Structures, 27, 2288-2299. [DOI:10.1016/j.istruc.2020.07.062]
12. [12] Mashayekhi, M., Estekanchi, H. E., & Vafai, H. (2019). Simulation of endurance time excitations via wavelet transform. Iranian Journal of Science and Technology, Transactions of Civil Engineering, 43(3), 429-443. [DOI:10.1007/s40996-018-0208-y]
13. [13] Mashayekhi, M., Estekanchi, H. E., & Vafai, H. (2019). Simulation of Endurance Time Excitations Using Increasing Sine Functions. International Journal of Optimization in Civil Engineering, 9(1), 65-77.‎
14. [14] Mualla, I. H., & Jakupsson, E. D. (2010). A rotational friction damping system for buildings and structures. Proceedings of the Danish Society for Structural Science and Engineering, 98(3), 47-98.
15. [15] Mualla, I. H. (2000, April). Parameters influencing the behavior of a new friction damper device. In Smart Structures and Materials 2000: Smart Systems for Bridges, Structures, and Highways (Vol. 3988, pp. 64-74). International Society for Optics and Photonics. [DOI:10.1117/12.383171]
16. [16] Hariri-Ardebili, M. A., & Mirzabozorg, H. (2014). Estimation of probable damages in arch dams subjected to strong ground motions using endurance time acceleration functions. KSCE Journal of Civil Engineering, 18(2), 574-586. [DOI:10.1007/s12205-013-0264-6]
17. [17] Hariri-Ardebili, M. A., Sattar, S., & Estekanchi, H. E. (2014). Performance-based seismic assessment of steel frames using endurance time analysis. Engineering Structures, 69, 216-234. [DOI:10.1016/j.engstruct.2014.03.019]
18. [18] Mashayekhi, M., Estekanchi, H. E., Vafai, H., & Ahmadi, G. (2019). An evolutionary optimization-based approach for simulation of endurance time load functions. Engineering Optimization, 51(12), 2069-2088. [DOI:10.1080/0305215X.2019.1567724]
19. [19] Mashayekhi, M., E Estekanchi, H., & Vafai, A. (2020). Optimal objective function for simulating endurance time excitations. Scientia Iranica, 27(4), 1728-1739. [DOI:10.24200/sci.2018.5388.1244]
20. [20] Estekanchi, H. E., Riahi, H. T., & Vafai, A. (2011). Application of Endurance Time method in seismic assessment of steel frames. Engineering Structures, 33(9), 2535-2546. [DOI:10.1016/j.engstruct.2011.04.025]
21. [21] Riahi, H. T., & Estekanchi, H. E. (2006, September). Application of endurance time method for estimating maximum deformation demands of structures. In First European Conference on Earthquake Engineering and Seismology, Geneva, Switzerland (pp. 3-8).
22. [22] Riahi, H. T., & Estekanchi, H. E. (2007). Comparison of different methods for selection and scaling of earthquake record time histories, In 5th International conference on seismology and earthquake engineering.
23. [23] FEMA, Improvement of Nonlinear Static Seismic Analysis Procedures. FEMA-440, Federal Emergency Management Agency, Washington (DC), 2005.
24. [24] BHRC. Iranian code of practice for seismic resistant design of buildings, standard no. 2800-05. 3rd ed. Tehran: Building and Housing Research Center, 2005.
25. [25] Office of collection and extension of national building code, section 10: Design and construction of steel structures, 4th ed. Tehran, 2005.
26. [26] American Institute of Steel Construction, Allowable Stress Design Manual of Steel Construction, 9th ed. Chicago: AISC, 1989.
27. [27] ASCE standard ASCE/SEI 41-06, Seismic Rehabilitation of Existing Buildings, American Society of Civil Engineers, 2007.
28. [28] Mirzabagheri, S., Sanati, M., Aghakouchak, A. A., & Khadem, S. E. (2015). Experimental and numerical investigation of rotational friction dampers with multi units in steel frames subjected to lateral excitation. Archives of civil and mechanical engineering, 15(2), 479-491. [DOI:10.1016/j.acme.2014.05.009]
29. [29] Riahi, H. T., & Estekanchi, H. E. (2010). Seismic assessment of steel frames with the Endurance Time method. Journal of Constructional Steel Research, 66(6), 780-792. [DOI:10.1016/j.jcsr.2009.12.001]
30. [30] Shirkhani, A., Farahmand Azar, B., & Basim, M. C. (2020). Optimum slip load of T-shaped friction dampers in steel frames by endurance time method. Proceedings of the Institution of Civil Engineers-Structures and Buildings, 173(10), 746-760. [DOI:10.1680/jstbu.18.00169]

Add your comments about this article : Your username or Email:
CAPTCHA

Send email to the article author